Showing posts with label Knives. Show all posts
Showing posts with label Knives. Show all posts

Saturday, January 6, 2018

Bark River Knife Set - North Country EDC &Featherweight Fox River

This set of Bark River knives were purchased along with a dual knife sheath for hunting.  The smaller of the two knives is a Featherweight Fox River and works exceptionally well for cleaning a deer.  The slightly larger of the two is a North Country EDC which was selected for skinning deer.

The knives are exceptionally nice.  They are both first production knives.  At this point they have only been used to process one deer.  The downside I noticed then was that the handles would get slippery with blood.  

Bark River North Country
Overall Length: 7.775
Blade Length: 3.5
Blade Thickness: .156
Steel: A2

Bark River Featherweight Fox River
Overall Length: 7.125
Blade Length: 3.125
Blade Thickness: .093

Steel: Elmax








Monday, December 11, 2017

Ben Akin Wapiti

This Wapiti design knife was produced by Ben Akin.  It was designed as a hunting knife which was also capable for camping chores.  The blade is 5" in length with a drop point design.  The spine is ground at a 90 degree angle for scraping ferro rods or hides.

The knife is exceptionally well balanced with the balance point being about where you second finger is at on the handle.  This makes the knife feel as if it weighs almost nothing despite being 9 3/4" in length.  This also ensures there is good control of the blade without any fatigue from use.

The blade itself is made from 01 tool steel which has been heat treated and oil quenched.  The blade them received a double temper cycle to improve toughness.  The flat grind makes the edge exceptional at cutting.  

The handle is made from bocote with black g10 liners and pins.  The handle is bonded together with Acraglas.  





I obtained this knife through a trade using an online forum.  When the knife arrived, it did not have the appearance of being maintained very often.  I spent some time cleaning up the flat edges with some 800 grit sand paper and then used a strop to clean it further and then perfect the edge.  A little Obenhauf's on the handle and sheath fixed them up to what is seen above from the starting point below.





Sunday, November 26, 2017

Adventure Sworn Huntsman #550

For quite a while, I viewed the Adventure Sworn Huntsman as the perfect hunting knife.  Adventure Sworn knives are custom made and I had thoughts of using it for years and it being such a well made knife that I give it to one of my children.  Perhaps it even comes to mind as something they hope to receive from me when I pass due to the frequent use and memories of me using the knife.

In reality, the knife has not been used much as I feel it is a bit too large for my needs.  The knife is just of such high quality, I've not considered selling it.  I take it out occasionally, look it over in admiration, and then place it back on the shelf in the closet.  The time has now come to sell it because there are no memories of using it or reason to keep it if it does not suit your needs.

Each Adventure Sworn is individually numbers and comes with a letter from the maker.  This particular knife is number 550.  The details of the knife are summarized in the letter"

Steel: 01 Tool Steel
Blade Thickness: 5/32"
Grind: Convex
Handle: Desert Ironwood w/Yellow Liners
Handle Thickness: 4/5






Saturday, April 30, 2016

Halfbreed Decker Hand Forged Knife

I picked up the following knife on the BushcraftUSA forum a few months back.  

The knife is made by Nate Hardin in Indiana under the name Halfbreed.  This is his Decker style knife which is hand forged 1095 steel with a convex edge.  The handle is green micarta with orange liners.  It has a kydex sheath with a Spyderco belt clip.  

I've only used the knife a little so far.  Its not the normal style knife I would go for but the build quality is exceptional.  If I could change something about it, I would make the clip point end a little more gradual on the to side.  I'm going to use it a little and see how it works for me.






Spine Modification (5/29/16):
I decided to work on the spine of this blade a little.  The clip style end was not very appealing to my eye as it dropped steeply over a short distance.  I decided to make it a little more gradual slope towards the tip of the knife.  

I used an air drill with sanding attachment to take metal off.  I had a fan blowing on it at all times and would just grind for a second and then let the blade cool for a minute.  The blade was never hot to the touch really.  It was probably a little overkill on my part to take so long but I did not want to damage the temper of the blade.  

Once I was done, I sanded with 100, 220, 600, and then 1500 on the spine to get it nice an polished like it was originally.  I considered putting a 90 degree edge on part of the spine for using a firesteel but decided against it.  

I'm quite pleased with the outcome and if you did not know any better you would think it was made this way.  A side benefit of removing the material is that the blade does not look as bulky and thick near the end.  

Before Picture:

After Picture (Traced outline on the paper is of the old blade shape):

A little more about the maker from a local newspaper article:
http://wildindiana.com/a/from-stone-age-to-steel-halfbreed-knives/



Sunday, February 14, 2016

Randall's Adventure Training (RAT) RC-4 Knife

The following knife is a Randall's Adventure Training (RAT) RC-4.  It is the precursor to the Esee 4.  

I purchased the knife used with an excellent convex grind.  This is the first knife I have purchased which I could easily sharpen to the point it cut hair off my arm.  Unfortunately, I only used the knife a handful of times.

The thin handle and thickness of the blade from cutting edge to spine made it feel a little clumsy.  The knife was certainly sharp but it seemed there were only a few things it did exceptionally well.  It was certainly not good for feather sticks, carving, or any kind of intricate work.  I worked on the spine some to get a good 90 degree but it didn't do well at striking a fire steel.

I added a few green liners in order to thicken the handle.  They also added a bit to the appearance of the knife.  I did not glue them in but instead just had them held in place by the three screws.  I was a little worried but the handle still locked into the sheath despite being thicker than normal (by about 1/8").

These knives are highly recommended but it just did not work for me.  I ultimately sold it off to someone else using the Bushcraft USA forum in order to gather money to try out something different.  I used the money to get the Halfbreed Decker shown on this site.





Friday, February 12, 2016

Mora Bushcraft Black Knife

I purchased this Mora Bushcraft Black thinking it would be an ideal outdoor knife for scouting trips.  Ultimately, I ended up selling the knife recently to consoldiate and end up with a fewer number of really nice knives.

The handle and blade are exceptional and it was very easy to use.  The knife was a little long for scouts as we tend to only allow scouts to carry a knife the width of their palm.  What bothered me is the finish on the blade started to discolor as if it were attempting to rust.  The black finish also did not hold up very well on the scandi grind when I stropped the knife.